Plate calculator: plates per side
Enter the weight you want on the bar. You get the plates for each side, a picture of the loaded bar, and the nearest weight you can load if your plates cannot make it exactly.
Calculator
How the plates are chosen
The calculator takes the bar off the target and halves what is left, because the plates go on in pairs. 100 kg on a 20 kg bar leaves 80 kg, so 40 kg on each side: a 25 and a 15. It takes the heaviest plates first, which keeps the number of plates down and keeps the heavy ones on the inside of the sleeve, the usual way to load a bar.
When the plates you have cannot make the weight exactly, it says so and shows the nearest weight below and above that you can load. 101 kg on a 20 kg bar is a case in point: 40.5 kg a side needs a 0.5 kg plate that the standard sets do not have, so you get 100 kg and 102.5 kg. If your gym has smaller plates, turn on the ones it has, or load the closest weight and keep a note of it.
It assumes you have as many of each plate as the lift needs. Real racks run short of a size: turn that plate off and the calculator finds what can be loaded without it.
Standard bars and plates
| Bar | kg | lb |
|---|---|---|
| Standard men's barbell | 20 | 45 |
| Women's barbell | 15 | 35 |
| Light or technique bar | 10 | Check the sleeve |
Metric plates come in 25, 20, 15, 10, 5, 2.5 and 1.25 kg, and competition plates follow a colour code: red 25, blue 20, yellow 15, green 10, white 5. Pound plates are 45, 35, 25, 10, 5 and 2.5 lb, and a 45 lb plate is about 20.4 kg. Gym plates are not always accurate, and a bar in a commercial gym may not weigh exactly what it says, so for tracking the same bar every week matters more than the third decimal. If your bar is not one of these, choose Custom and type its weight.
Kilograms and pounds
Switch the units and the target converts, the bar goes to the usual bar of that system and the plate set changes to the pound set. A kilogram target is not always loadable in pounds and the other way round: 100 kg is 220.5 lb, and with pound plates the closest loads are 220 and 225 lb. Keep to the plates your gym has.
Logging the weight in a journal
Log what was on the bar, the total weight, not the plates per side. In AIm you log each set with its weight and reps, in the app or by telling Claude or ChatGPT. When you run a workout in the app, each set shows what you did last time on that exercise, so you know what to load, even if you load it differently from one week to the next. AIm does not work out plates for you, so use this page for the loading and log the total.
Other tools in this set: the 1RM calculator (your one rep max from any set), the DOTS calculator (DOTS and Wilks scores), the RPE calculator (the RPE chart and working weights), the tonnage calculator (the volume load of a workout).
Sources
The loading is arithmetic and needs no source. The bar weights and the colour code are common practice, and the link shows the bars and colour coded plates used in IPF approved equipment.
Frequently asked questions
How many plates do I need for 100 kg?
On a 20 kg bar, 40 kg on each side: one 25 kg plate and one 15 kg plate, four plates in total.
How do I calculate plates per side?
Subtract the bar weight from the target and divide by two. That is the weight on each side, which you build from your plates, heaviest first.
What does a standard barbell weigh?
20 kg (45 lb) for the standard men's bar and 15 kg (35 lb) for the women's bar. Lighter technique bars weigh 10 kg or less. Check the sleeve or the manufacturer if you are unsure.
What if my target cannot be loaded with my plates?
The calculator shows the closest weight below and the closest above. To bridge a small gap you need smaller plates, so turn on every plate you have.
Does it work in pounds?
Yes. Switch to lb for a 45 lb bar and the 45, 35, 25, 10, 5 and 2.5 lb plates. You can also type your own bar weight.